Furniture design
Doors and opening directions
Choose hinged, double, sliding, drop-down, or lift-up doors and understand their fit rules.
On this page
In Free Design, select a compartment and open Selected → Doors & drawers to choose a door for that opening. Then select the door itself to edit its type and details. In a guided category, the section’s Function or Front control can own the door type while the selected door still exposes its useful opening direction.
Door types
| Control | How it opens | Supported opening envelope |
|---|---|---|
| Opens from left | Pull from the left; hinges sit on the right | 20–100 cm wide, 15–240 cm high |
| Opens from right | Pull from the right; hinges sit on the left | 20–100 cm wide, 15–240 cm high |
| Double doors | Two side-hinged leaves meet in the middle | 40–240 cm total width, 15–240 cm high |
| Sliding | Leaves slide across the front | 80–360 cm total width, 40–270 cm high |
| Drop-down | Pull from the top; it swings down on a hinge along the bottom | 20–180 cm wide, 15–100 cm high |
| Lift-up | Pull from the bottom; it swings up on a hinge along the top | 20–180 cm wide, 15–100 cm high |
The live editor is authoritative and can impose a smaller limit for a guided category, connected layout, material, or hardware combination. A single side-hinged leaf is physically supported up to 100 cm, but Supernata prefers a double-door solution above about 60 cm when it chooses for you because the swing is easier to use and the leaf is less likely to warp.
Read left and right correctly
Opens from left names the side you pull, not the hinge. Its hinge is on the opposite edge. Use the automatic 3D opening preview to confirm the choice, especially for a cabinet beside a wall, another door, or a circulation path.
In Posisi, the point of the dashed V marks the hinge edge of each leaf, including both leaves of double doors. The hinge symbol follows the displayed face in a mirrored corner view.
Why a type is unavailable
A grey option can mean the opening is too narrow, wide, short, tall, or shallow; that a drawer-only slot is selected; or that the requested door would conflict with an open side or another structural rule. Tap the option to see the live reason. Change the compartment size, choose another type, or return to the section function instead of forcing an incompatible front.
Doors across several spaces
A hinged door can contain adjustable shelves and Maximera drawers behind it. Use Split door into compartments when those zones need separate outside fronts. In the dedicated placement flow, a single door can merge several spaces only when they are contiguous vertically, have equal width, and belong to the same section and column. Multi-space placement supports door types, not drawers or drop/lift fronts. Double and sliding doors can span a larger section but still depend on the underlying section geometry; check that the requested opening belongs to the intended column.
Sliding doors in front of drawers
A sliding unit can cover drawer compartments. Keep one opening without a drawer to carry the unit. Drawers behind it sit back behind the rear leaf, with room for a bar handle, and their boxes are cut shorter by the same amount; a drawer opens once the leaf in front of it slides aside. When the cabinet is too shallow for drawers behind the leaves, the studio says so: make the cabinet deeper or leave those drawers out of the sliding unit. Like other shared doors, a sliding unit is confirmed by the workshop before payment.
Finish per leaf
On a sliding unit, Finish per leaf gives one leaf its own finish. Tap the leaf (left, middle or right), then a swatch or Make … a mirror. Match door returns it to the door finish.
Lifting lid (Tutup angkat)
Choose Lifting lid among the door types for the top box of a column. The box closes at the front with a fixed panel and opens at the top on a lid with hydraulic stays. The lid settings add Mirror under and Lock, and Open the lid previews it. A lid needs the top box of a column, 15–120 cm wide, in a cabinet at least 25 cm deep, with nothing on top: no cabinet resting on it, top trim, cooktop, sink, cushion, light, cable hole or stone/HPL top. If a later change makes the lid impossible, its settings say why, the front works as an ordinary door again, and checkout waits until the lid is removed or fixed. The hydraulic stays have no supplier price yet, so a design with a lifting lid is quoted before payment.
Sliding lid (Tutup geser)
In the lid settings, How it opens switches a lid between Lift and Slide. A sliding lid comes straight out to the front on one pair of push-open drawer runners, priced like a drawer's runners, instead of stays and hinges. It needs a body at least 30 cm deep, inset fronts (an overlay front covers the lid's front edge), walls on both sides of the box, and no mirror under it. Cable notches cuts up to four notches into the lid's back edge for cables: Add a notch puts one where it fits, and the chips on the top view set From the left, Width and Depth. Each notch needs 3 cm of board at each end of the lid and between notches, and can be at most a quarter of the lid depth (8 cm at most). If a later resize leaves a notch without enough board, the settings and checkout say so; the notch is never moved for you. Slide it out previews it.
Small glass slider (Kaca geser kecil)
For a box 40–120 cm wide and 20–100 cm high that is too small for the board sliding kit, choose Small glass slider among the door types. It closes the box, or several boxes side by side in one cabinet, with two frameless glass leaves on a light aluminium track. Choose 4, 5 or 6 mm glass. Under Grip, Finger hole drills one Ø 2.5 cm hole near the bottom outer corner of each outer leaf; the chips on the picture set From the edge and From the bottom, and a hole that would leave less than 1 cm of glass around it is refused. The glass is priced; the track and the finger holes are confirmed at quotation.
Customize the selected door
The door detail includes:
- opening direction or full door type;
- shelves and ready-made layouts behind a hinged door;
- handle style and available finish;
- front and interior surface;
- color or custom finish;
- automatic ventilation grille where it fits;
- a specification lock toggle.
These appearance controls are explained in handles, surfaces, ventilation, and locks. Drawers and hidden drawers have their own rules in drawers and Maximera.
Still need help?
Contact us with the studio, device, and what you were trying to do.