Skip to article

Room Planner

Room doors, windows, coverings, and opening rules

Place exact door and window presets, set hinges and swing, edit coverings and colors, and resolve invalid openings.

10 min readLast updated Public guideMarkdown
On this page

Doors and windows are openings hosted by an exterior or interior wall. Add and edit them in Build mode. The plan view is best for left-to-right placement and swing clearance; the 3D view is best for sill height, appearance, and room context.

Place an opening

  1. Open Build → Openings.
  2. Choose Door or Window.
  3. Pick the type before placement if the default is not correct.
  4. Tap the target wall. The ghost shows the real opening size and turns invalid where it cannot fit.
  5. Continue placing openings, then select Done to put the tool away.

You can move a selected opening along its wall. A window can also be dragged vertically in 3D. Helpful snaps include the wall centre, even gaps between neighbouring openings, floor level, the standard 90 cm sill, and the highest valid sill.

Door presets

TypeWidth × heightOther controls
Single90 × 210 cmLeft/right hinge and inward/outward swing
Double180 × 210 cmLeft/right hinge and inward/outward swing
Sliding180 × 210 cmHinge and swing controls are hidden
No leaf (passage)100 × 220 cmAn open doorway with its frame

Changing the type applies that type’s preset dimensions. You can then enter a custom width and height within the limits below.

Curved openings

The door and window settings no longer offer Rounded or Arched. A door or window that is already curved keeps its shape and shows Make it straight, which turns it back into a square opening. While it is curved, the wall, its finishes, the frame, the leaves and the glass follow the curve, and the plan and wall drawings print it. A sliding door’s glass panels are cut to the arch too. A curved opening costs the same as a square one.

Window presets

TypeWidth × heightSill from floor
Standard100 × 120 cm90 cm
Double200 × 120 cm90 cm
Small60 × 60 cm140 cm
Large150 × 150 cm70 cm
Full height100 × 240 cm0 cm

A window can use None, Curtain, Roller, Vertical, or Roman covering. Set the glass, frame, and covering colors in the selected-window panel. A door has separate leaf and frame colors.

For a flat front view, select the wall in Plan, open Selected → Wall focus, and add a window there. The same presets, coverings, and colors are available. Position and size edits stay within the displayed room-facing wall section and must pass the opening and wall-equipment fit checks.

Custom limits and validation

The editor accepts a custom opening 30–500 cm wide and 30–400 cm high. A window’s height is typed on its two chips in 3D: the sill chip below it (height above the floor) and the head chip above it (gap to the ceiling). Typing the head gap moves the window up or down and keeps its size. Both chips accept 0 up to the wall height minus the window height. A value outside that is refused with its range, for example Enter between 0 cm and 160 cm. for a 120 cm window on a 280 cm wall. A chip is hidden while its gap is 2 cm or less. A door stands on the floor, so its chip above only shows the gap to the ceiling; change the door’s height in Selected.

An opening is valid only when its entire width stays on the finite wall and it does not overlap another opening. A jamb may sit flush with a wall end in the current planner; there is no extra opening-to-corner margin. This is different from furniture placement, which keeps a separate 15 cm lateral buffer beside an opening. A wall can also reject an opening that is too short or has no usable physical height.

Edit and delete safely

Select the opening in Plan, 3D, Structure, or Selected. Change its type, size, hinge, swing, covering, and colors in Selected. Its position is typed on the dimension chips: the side gaps in Plan or 3D, measured to the next opening or the wall end (in 3D also to an item hung on the wall), and the sill and head gap in 3D. They type like every chip; see Type an exact value on a chip. In 3D, a side gap that would overlap an item on the wall, or jump past one, is refused with This overlaps an item on the wall. Try another gap. Deleting an opening does not show a confirmation because Undo can restore it as one action. Use Undo immediately if you selected the wrong opening.

Always inspect real door-leaf travel, handle clearance, curtain stack, and furniture circulation. The plan validates geometry, but it does not know every hinge, trim, jamb, electrical, or site condition.

Lock a gap to the wall end

The gap chip that reaches the end of the wall carries a lock. In Plan it is the first or last gap in the wall’s dimension chain; in 3D it is the side chip that measures to the corner. Tap the chip, then tap the padlock beside its input (Lock the gap to the corner). A number you typed is saved and locked together, so one Undo takes back both. A locked chip shows a small padlock and cannot be typed.

A locked gap keeps the opening that far from the wall end. If the wall gets longer or shorter, the opening moves with that end. A change that would alter the locked gap, such as dragging the opening, is refused until you unlock it. To unlock, tap the chip and tap the padlock again. The chip stays open so you can type a new gap right away.

On a phone, the opening sheet lists each locked gap as Left gap locked · 40 cm or Right gap locked · 40 cm, with Unlock. Left and right are named as you face the wall from inside the room. For an interior wall, that is the room you are working in, shown under the row as Seen from and the room name. The list keeps a lock reachable even when another opening now sits between this one and the corner, so no chip carries it.

Place furniture around the finished openings with Cabinets, furniture, and placement.

Still need help?

Contact us with the studio, device, and what you were trying to do.

Contact & help