Skip to article

Room Planner

Measurements, 2D and 3D views, wall views, and tools

Read and edit dimensions, measure between two points, show clearances, control wall visibility, and recover the camera.

9 min readLast updated Public guideMarkdown
On this page

Use the Plan view to author geometry and the 3D view to judge volume, reach, and visual relationships. Both read the same centimetre-based document, but they expose different controls.

Plan view and editable dimensions

Plan (2D) looks straight down and shows wall lines, openings, swing arcs, furniture footprints, partitions, and dimension chains without perspective. In Build mode, select a wall number to enter an exact length. Selected openings show their own width and clear gaps along the host wall. Partitions expose editable segment lengths and junctions.

Use Show dimensions to display the relevant architectural and object labels. Hiding labels changes only the view; it does not delete measurements.

To see a flat wall elevation, tap the wall itself in Plan and choose Selected → Wall focus. The picked location identifies the uninterrupted wall section facing that enclosed area, rather than the entire outer edge across several rooms. Check its area name and use Other side for the opposite partition face. If a Structure selection is ambiguous, pick the intended section in Plan first. Select an item on the elevation to show its chips: its distance from the displayed left edge, plus the sill height of a window or the centre height of a socket, network point, switch, or AC. A door only has its distance from the left. Type on them like any chip, or drag the item on the elevation. With an item focused, the arrow keys move it 1 cm, and 10 cm with Shift.

For an air conditioner, choose its PK capacity before adding it: 0.5, 0.75, 1, 1.5, 2, or 2.5 PK. The recommendation uses the area facing the selected wall. Body dimensions and top/side clearances are editable planning assumptions, not specifications for a purchased model. Confirm those values and capacity for the actual equipment; visible furniture provides context rather than a complete installation-clearance check.

3D view and wall visibility

3D is best for ceiling height, window sill, furniture height, door movement, wall-mounted items, finishes, and lighting. Choose:

  • Full walls for the complete enclosure.
  • Cutaway walls to lower camera-facing exterior walls while preserving readable interior divisions.
  • Low walls for a mostly open overview with low wall bases.

A hidden wall still exists. Return to Plan or choose Full walls before concluding that a wall or opening was deleted.

Clearances and object dimensions

Select a floor object in 3D, or turn on Dimensions in Plan, to show its distances to walls, openings, and nearby furniture. A wall item shows vertical and along-wall relationships relevant to its host. These distances are chips you can type on; see Add cabinets, furniture, and decorations to a room. Clearance labels are design aids; check door swing, body movement, installation path, and any manufacturer service zone separately.

Measure any two points

Choose Measure distance, then tap two points in Plan or 3D. The ruler reports the straight distance and component differences available in the current view. Use Done, Escape, or the tool-cancel action to clear the temporary ruler. A ruler result is temporary unless you save it with its pin button (Save measurement), which keeps it in the room as fixed points. Neither changes the design; use a wall or object dimension control when a value must change it.

Saved measurements show while Dimensions or Measure is on. To change one, turn on Measure. Drag either end to move it; the ends snap like the ruler. Or tap its length chip and type a new length: the start point and the direction stay, and the far end moves. Tap its pin label to open Saved measurement. There you can rename it under Name, tick Guide without dimension value to hide its number, or choose Delete measurement. A saved measurement is a pair of fixed points; it does not follow an object you move later.

Camera recovery

Use Fit to screen after importing, reshaping, or moving something far away. In 3D, drag empty space to orbit and scroll or pinch to zoom. In Plan, pan and zoom without using an object handle. If a touch gesture keeps moving an object, cancel the active tool or clear the selection before navigating.

Undo, redo, and Escape

  • Command/Ctrl Z undoes the last grouped design action.
  • Command/Ctrl Shift Z or Ctrl Y redoes it.
  • Escape closes a transient tool or selection context when no dialog owns the key.
  • Delete/Backspace removes a supported selected object; destructive room deletion still has its own confirmation.

Painting and long drags are grouped rather than creating one history item per pointer movement. Some view and mood changes intentionally do not enter design history.

Find a buried tool

Open command search with Command/Ctrl K and search for Plan, 3D, full walls, cutaway, low walls, dimensions, clearances, measure, fit, undo, redo, or the action you need. The live command list is the best reference for what the current mode and selection can do.

For general orbit and touch behavior, read Navigate and select in 3D.

Still need help?

Contact us with the studio, device, and what you were trying to do.

Contact & help