Furniture design
Design with RAKAI AI
Turn a description or reference image into an editable furniture design.
On this page
RAKAI is the AI designer inside Shelf Maker. It creates and edits the same parametric cabinet structure used by the manual controls, so the result stays selectable and adjustable.
Write a useful request
Include the furniture type, overall size, main functions, and preferred finish. For example:
Create a 220 cm wide wardrobe in Opera Grey, 240 cm high and 60 cm deep, with two hanging sections and four drawers at the bottom.
Specific measurements are better than words such as “large.” If one detail matters most, say so explicitly.
Refine instead of restarting
After RAKAI creates a design, ask for one coherent change at a time: “make it 40 cm deep,” “add a section on the right,” or “change the lower compartment to four drawers.” You can also continue with the manual controls. Manual and AI edits operate on the same design.
Point at the part, then say what to change
Use the pin with a plus in the RAKAI message box (Tambah titik) to click one part, or the pen in the same row (Tandai area) to circle it or drag a box around it. A loop counts what it encloses: circling an opening picks that opening even when the line clips its neighbours, a loop around a door picks the door, and a loop down a whole column picks the column. A numbered request opens there: write the change, then Simpan to queue it or Tanya Rakai to send it now. Your words decide what in the area changes. “Jadikan laci” on a circled door changes the opening behind it, “tambah ambalan” goes inside, and a part that cannot take the change is refused with the same reason the editor gives. If more than one part fits, the request names them: add “yang kiri”, write “semua” for a whole column, or mark one part again. Saved requests wait in the request list. The list button beside Send shows how many there are and opens the list above the message box, where Jalankan semua runs them in order. When only archived requests are left, the button shows the archive icon and opens Arsip.
For B2B work, name the target and the exact choice: “use PVC for this shelf board,” “apply this AICA article to Row 2,” or “set this shelf 8 cm back from the front.” RAKAI can search catalog references and use the same material, finish, handle, runner, hinge, grouped-front and Quadra controls. It checks saved design state before claiming a supported request is complete. Unknown product identity or fabrication evidence stays unresolved. Structural rebuilds that would discard authored B2B details are refused; use the supported native edit or Undo.
Sketch it: in 3D or on a blank board
Sketsa in the RAKAI message box (the squiggly line, or type /sketsa) offers two choices: Di 3D and Papan kosong. Every sketch belongs to a request point (Permintaan), so RAKAI reads it together with your words, and Jalankan semua runs the points in order: 1, 2, 3.
Di 3D draws right on the cabinet with the same bar as a note: a pin, box, revision cloud, circle, line, arrow and pen, with colours and thicknesses. Teks puts words where you tap; Ukuran draws a size line and asks its real size (an empty size keeps only the drawn line, shown with ≈). A typed size is the size RAKAI works to. The first stroke places the point on the part under it. Pakai opens the point's card. Write what to change and the sizes ("bawah jadi 2 laci, 35 cm"), then Simpan keeps the point in Permintaan with its number on the cabinet, or Tanya Rakai sends it now. Tap the point later to open its card again; its sketch shows as Sketsa di 3D and opens to keep drawing. In the request list each point shows a small picture of its board drawing or photo, else of its 3D sketch, so sketched points are easy to tell apart.
A point's card also has Papan kosong: draw on a blank board and Pakai puts the drawing on that point as its picture. The drawing reopens from the card on this device. A point holds one picture, so a board drawing replaces a photo and the other way round. Notes for the workshop (Catatan 3D) offer the same Sketsa di 3D and Papan kosong; their sketches print on the drawing's note pages.
Draw a new cabinet on a blank board
No cabinet yet, or easier to draw it flat? Sketsa → Papan kosong (or /papan-sketsa) opens a blank board. Draw the front with the pen or shapes, write words, and use Ukuran to type each size (200, 2 m or 850 mm). The lines are never to scale, so RAKAI builds to the typed sizes. Pakai attaches the board to the message as one picture marked Papan and fills in "Buatkan lemari seperti sketsa ini."; tap the picture to keep drawing. The attach button is for photos and files.
Send it now, or press + beside Send to keep the message, board and all, in Permintaan for later, as Room RAKAI does. A kept message is for the whole design: it has no pin and no number, and its row shows the picture. Tap it to bring it back into the message box, change it and keep it again with ✓, or send it. × removes it. Jalankan semua sends the kept messages that have not run yet first, in order, then the points; a message that ran is not sent again unless you send it yourself. Kept messages stay on this device with this design; + is off while a part is chosen as the target (use Tambah titik for a part).
Use reference images
Attach up to eight images, such as exterior and interior views of one cabinet, drawer details, a measured drawing and a design reference. RAKAI combines them automatically. Add the known dimensions and what must be preserved. You stay in Shelf Maker with the cabinet visible while RAKAI works.
Use clear images with visible section boundaries and limited perspective distortion. Label measured dimensions in the image or message; an unmeasured photo does not verify scale. To change the current cabinet using another image, describe the change explicitly. Ask for a new design when you want to start over.
Leave space for appliances
Ask in chat for an oven, microwave, fridge or other supported appliance opening, with its required clear dimensions. Select a bay when the request concerns that part of the cabinet. RAKAI stores the space requirement and checks the actual opening; it does not insert an appliance model. You can ask to change or remove the requirement, then use ordinary cabinet controls to adjust the geometry. Unknown dimensions remain unverified. Appliances are not included. Quadra worktop cutouts can be recorded separately with explicit dimensions and references; this does not certify the appliance installation or price its fabrication labor. A quoted opening does not establish installation readiness.
Your chat history
Signed in, your RAKAI chats belong to your account. Chat history shows them on every device where you sign in, and deleting a chat removes it everywhere. Signed out, or with another account signed in on the same device, none of them show. Photos you attached stay on the device that sent them.
Understand the limits
RAKAI may clamp dimensions, adjust a layout, or refuse a function that cannot be built within the available space. These warnings remain visible; open Show details for the other build notes. Inspect the 3D result and verify all critical dimensions. AI output is an editable starting point, not permission to skip site measurement or professional fabrication checks.
Still need help?
Contact us with the studio, device, and what you were trying to do.